Repair Static Routes Not Working TutorialHome > Not Working > Static Routes Not Working
Static Routes Not Working
asked 2 years ago viewed 9260 times active 2 years ago Blog How We Make Money at Stack Overflow: 2016 Edition Stack Overflow Podcast #94 - We Don't Care If Bret Verify whether the IP address of ONS 15454 specified on the workstation matches the IP addresses that appear on the LCD screen of the remote ONS 15454s. In this configuration all computers from both networks can access ( ping, file transfer) each other ( by IP or by name). You do not know whether the default router entry for the ONS 15454 is set correctly to match the IP address of the next hop router's interface.
Why didn't "spiel" get spelled with an "sh"? Background Information This document begins with how to establish link level connectivity, and moves on to describe how to configure and troubleshoot IP connectivity on the 15454, Cisco routers, and the Understand the 15454 Routing Table In order to achieve CTC connectivity to each other, all of the interconnected 15454 network elements in a ring form an Open Shortest Path First (OSPF) Figure 27 – Scenario 7 IP Checklist for Scenario 7: Are the two CTC workstations IP addresses and all the ONS 15454s IP addresses on the same subnet? http://stackoverflow.com/questions/10605240/why-doesnt-static-route-work-here
Windows Static Route Not Working
Do the LAN wire-wrap pins on the backplane or TCC's RJ-45 port have link integrity? Prerequisites Requirements There are no specific requirements for this document. Verify whether the nodes have a name in CTC map view.
Best Regards ART See More 1 2 3 4 5 Overall Rating: 0 (0 ratings) Log in or register to post comments Richard Burts Fri, 02/12/2016 - 14:42 If you want Do you have a web browser installed (either Netscape Navigator™ version 4.08 or higher or Internet Explorer™ 4 and higher)? If your network is live, make sure that you understand the potential impact of any command. Windows Persistent Route Not Working Optical Carrier, level N (OC-N) ports are not in service.
I was able to figure out the problem. Windows Persistent Route Not Active Remove from profile Feature on your profile More Like This Retrieving data ... When the interface is restarted next the system will add any valid route in the route-eth1 file to the routing table. http://serverfault.com/questions/649675/static-routes-not-working-for-me share|improve this answer answered May 15 '12 at 16:46 David Mokon Bond 615724 Thank you for the answer, sir, really helpful, I forgot the Ping command is somewhat a
The static routes have the next hop IP address assigned to interface cpm0 on 15454-1 to which Router-C is directly connected. Active Route Vs Persistent Route When you configure the SDCC, never change the area ID or Disable OSPF on the SDCC unless you want to divide the network into different OSPF areas for management purposes. On this router interface there is not PAT configured interface GigabitEthernet0/1.425 description CLIENT425 encapsulation dot1Q 425 ip address 126.96.36.199 255.255.255.252 ip flow monitor MONITOR_CLIENT425 input ip flow ingress ip flow egress Verify the IP address of your workstation.
Windows Persistent Route Not Active
Or is it? It does look like the host has appropriate address, mask, and default gateway. Are the optical trunk ports on all nodes in service? IP Scenario 7 CTC 1 and 2 and all 15454s are on the same IP subnet. Static Route Not Working Cisco
The Java™ policy file was not installed or the file was installed before the Java™ plug-in. Conventions Refer to Cisco Technical Tips Conventions for more information on document conventions. Typically, you would plug the 15454 and the Personal Computer (PC) into a switch on the edge of each side of the routed network. Check the routing of the ONS 15454 and the workstation.
Is the hub or switch port for ONS 15454 #1 set for 10 Mbps half-duplex? Netsh Vs Route Add Are all of the IP addresses unique? Is the DCC enabled for all optical trunk ports that are in service?
Exciting Jobs Using Cisco Technology Cisco TAC Job Openings Create Your IT Career Create Your IT Career Create Your Career Toolkit & Webinars Internet of Things Webinar Series Women in Networking
Check file content looking for corruption, file size indicates size "zero" StackList
when 192.168.1.0/30 is up, it should route packets through it and only through it. Refer to these illustrations and checklists when you set IP addresses and configue subnets. I suppose that I have to define a new static route but indifferent of what I have tried ( from google, tips from friends) I do not get the desired result. Complete these steps: Click the Provisioning tab.
Verify whether trunk ports are in service through the CTC. Are the optical trunk ports on all nodes in service? Can the workstation that runs CTC ping itself? Does ONS 15454 #1 have static routes that point to the CTC workstation?
IP Scenario 6 CTC is on a different subnet and all 15454s are on the same subnet. 15454-1 is attached to LAN A, and 15454-2 and 3 are at remote sites. Note:The snap tab at both ends is to the back of the connector.