How To Fix Sundance Spa Jet Not Working Tutorial

Home > Not Working > Sundance Spa Jet Not Working

Sundance Spa Jet Not Working

Contents

If the filter just sits in a well behind a hole in the wall your life is much easier. I see that power is coming to the main circuit board. He should stop being so helpful. None of the breakers have tripped and the fuses all appear intact. Check This Out

BRANDMADE.TV 4,695 views 8:57 # 37 Why do spa heaters fail? - Duration: 9:12. Dr/Dry = Inadequate water flow detected in the heater. And then you throw your hose in for half an hour, turn it back on and Voila! When you fill your spa back up, many times the air that's in the equipment has no place to go, and is pinned in on each side by the water you've

Hot Tub Jets Not Working On One Side

As water begins to flow in toward the equipment you will hear the force of the air and water coming out increase. We have a La-z-Boy spa and the owners manual description for bleeding air produced more questions than it resolved. Also the power seems to go off sometime all together and the gfci box has tripped a few times but will reset and I can usually get things going again…But The Bought new filter, (this is when I found the gfci had tripped earlier in the week) I reset gfci put filter in and went to work.

Hope this saves somebody a service call! See instructions below. If you have any questions regarding these spa air lock solutions please feel free to leave a question in the comments below or email me directly at: [emailprotected] Thanks for reading Hot Tub Jets Weak Marie leopold Thank you…I have someone coming out Thursday so hopefully it will be something simple!

If you have any comments or suggestions, or if you wish to be informed on any new products for your hot tub, please write to us. Sign in Share More Report Need to report the video? Looked up how to tell if a relay is good or bad. http://www.sundancespas.com/customer-care/troubleshooting-procedures/ Ralph Sampson GFCI on a hot tub is not something to experiment with.

Otherwise you will get more water than you bargained for. In Ground Spa Jets Not Working A: If your spa pump is coming on, but not pumping any water here's some steps to troubleshoot. Loading... Therefore the easiest way to release this air pocket is to crack open the union nuts on the spa motor itself.

Hot Tub Jets Won't Turn On

Today we will look at 2 ways you can release an air lock in your spa. this This feature is not available right now. Hot Tub Jets Not Working On One Side Second, If the pump was recently replaced or rewired, the wires could be reversed on the back of the motor. Half Of Hot Tub Jets Not Working Air locks happen when we fill the hot tub from inside the tub and water falls into the plumbing from the jets, this pushes all the air that is in those

If you didn't just drain your tub and you don't think you have an air lock, try the following: 1) Is the high speed pump working? Of course, you'd never have gotten yourself into this situation if you'd just closed the valves on either side of the equipment before you drained it. Each union and drain plug represents a spot in the equipment where we can bleed the air from. That depends. Hot Tub Air Lock Symptoms

Checked fuses and transistors for light and board. Change it them test all lines in until you find the issue. Apologies if this is already written up somewhere or misplaced. Remove it for a few minutes from the spa and see if the jet action improves on hi speed with no filter.

Barbara July 28, 2014 at 7:13 pm Hi! Bathtub Jets Not Working Checked for continuity and power of all incoming wires and transformer. The cover got ruined by heavy snow so I took it off and drained it untill I could get another cover.

Why?

Hope not. Tweet Share53 Pin110 Share34Shares 197 This Is The Last Hot Tub Manual You Will Ever Need You'll save at least $100 off the bat with this easy-to-follow digital handbook. Just enough to let some water or air out. Hot Tub Pump Not Working If I had to describe it sounds like it's sucking Air and singing at the same time.

Loading... Nigel May 15, 2016 Reply Scott check to see that the motor shaft is not stiff or stuck. Look for debris clogging the impellor or a broken impellor. 3. You are here: HomeThe Pool BlogHow to release an air lock in your spa How to release an air lock in your spa October 20, 2010 by JayB 27 Comments

Your pack may vary significantly from the components described below. Tell us by commenting below! Rating is available when the video has been rented. You can follow any responses to this entry through the RSS 2.0 feed.

Jason Hughes 736,888 views 7:55 Pressure Switch Flow Code No Heat Spa Hot Tub How To The Spa Guy - Duration: 8:14. And then you throw your hose in for half an hour, turn it back on and Voila! It came on for a few seconds then quit. When Weather Tempature warmed up to 60 degrees in a few days I refilled the tub and flipped the breaker.

Turns out the transformer blew out two legs. By the way, love the new design. Tacticalterry Do u have two pumps? On the board when power is on and one solid led light and one flashing led light that says "flash ok" next to it.

Mario Gasperino My hot tub heats up as soon as I turn on all the jets. There could be a few things preventing your jets from pumping water. Keep burping the jets increasing the length of time you hold the jets on by 10 seconds each time. Our hot tub manual states to fill, or refill, through the filter housing to push all the air out of the plumbing.

Go find the plunger. You're so thorough at draining your spa that you evacuate every elbow, every little 1/2" line, and every piece of equipment until you know there's not a drop of moisture in November 10, 2013 Reply Doug what is the make and model of your spa and the date built? Ask an Expert Home Improvement Questions Pool And Spa Repair How JustAnswer Works: Ask an Expert Experts are full of valuable knowledge and are ready to help with any question.

EVNautilus 3,370,905 views 5:15 testing and replacing or servicing a hot tub or pool recirculating pump - Duration: 8:06. Most often this will be caused by a leaking shaft seal, or it could happen from old age. If not, the Circuit Breaker may be tripped. Your heater burned up from being exhausted from running with the top off.