How To Fix Sundance Spas Jets Not Working Tutorial

Home > Not Working > Sundance Spas Jets Not Working

Sundance Spas Jets Not Working

Contents

Now that it is getting hot outside (upper 80's to lower 90's) the GFCI is tripping every day around the same time (3-3:30PM). Turn the spa off, clamp the lid in place, spa back on, pump on high and you should be in business. I left out of town the next day and didn't come back for two days, when I noticed a storm had knocked my cover off and my tub was showing a If the filter just sits in a well behind a hole in the wall your life is much easier. Check This Out

Published on Jan 16, 2014Subscribe Now:http://www.youtube.com/subscription_c...Watch More:http://www.youtube.com/ehowatHomeChannelFixing an air lock in your spa is something that you would do only after draining out all the water. some have speakers and subwoofers and the one i have wont work i have tryed many types of i-pods and mp-3 players, the wires are all hooked up, i also would Checked for continuity and power of all incoming wires and transformer. If it is not coming on, then yes, you'll need them to come out to look at it as it's either a bad pump, bad board, or a blown fuse.

Hot Tub Jets Not Working On One Side

Janis Cuthbertson hot tub screen has flo on it replaced the flo switch cleaned the filters what could be wrong Matt Giovanisci You may need to replace your filters. Take the lid and push it into place, and then immediately take it off again. Fourth, the mechanical switch in the back of the motor could be stuck in the high position, due to broken parts or insect infestation.

Take the lid and push it into place, and then immediately take it off again. Janis November 3, 2015 at 11:18 am I have a Sundance Altamar hot tub. I truly appreciate you taking the time to explain the top caused the issue. Hot Tub Jets Weak Eric Howe January 27, 2011 at 3:07 pm thank you for the help you have to provide for me.

With the lid off, turn the spa on with the pump on low (do not hit the 'jets' button). Hot Tub Air Lock Symptoms There are 3 main approaches to cleaning. Apologies if this is already written up somewhere or misplaced. Low water will allow the skimmer to suck air, and cause the pump to lose prime.

softcellelectrical 83,237 views 2:57 Loading more suggestions... In Ground Spa Jets Not Working Our repair guy has replaced the circ pump, flow switch, and control panel. Air. Published on May 8, 2012Every so often, air can get stuck and stop your pump from working properly.

Hot Tub Air Lock Symptoms

Nicholas Rogers 4,685 views 1:32 # 36 Why doesn't my hot tub work - Duration: 4:15.

This is when we move on to the next method for releasing an air locked hot tub. Hot Tub Jets Not Working On One Side If the plunger gets stuck on the hole, turn the spa off and remove it. Hot Tub Jets Won't Turn On We tried removing the filter and using a plunger with no luck.

Take the filter out. You need to bleed the air out and replace it with water before the pump can catch prime. May need to get it replaced. Rating is available when the video has been rented. Half Of Hot Tub Jets Not Working

That's your cue to start tightening. If the filter just sits in a well behind a hole in the wall your life is much easier. As water begins to flow in toward the equipment you will hear the force of the air and water coming out increase. Third, is the switch in the back of the motor, that changes to motor from low speed to high speed.

Some spas have two pumps, one is the circulation pump and the other is the jet pump. Hot Tub Pump Not Working Tighten the cap finger tight, replace the handle, and turn the spaÕs power back on. Also look for loose or worn out jet seals and check the nozzles for obstructions Categories Accessories Chemicals Cover Removers Covers Filter Cartridges (Unicel) Filters Cartridges (PuraSpa Disposable) Fragrances Gift Ideas

Carri s April 16, 2014 at 9:00 pm We have tried burping and leaking the water from the union nut.

He moved and we were happy to get it from the new owner. Danny Smith Just rebuilt pump and new motor, now the motor keeps kicking out when I turn on jets. Tell us by commenting below! Bathtub Jets Not Working Otherwise you will get more water than you bargained for.

Second, If the pump was recently replaced or rewired, the wires could be reversed on the back of the motor. If you replace the Fuse and it pops again, you have an short in the wiring equipment of your spa. I was able to locate the drain plug on my spa and let enough air out to make the pump actually pump water again! I replaced them and it worked a little bit then it tripped again.

If a GFCI trips the very first thing you do is found out why it tripped.